How to Remove and also Replace a Bathtub.

Book Service

Just how do you feel when it comes to Tools You Need to Install a New Bathtub ?


A Step-by-Step Guide to Installing a Bathtub
Installing a bathtub isn't precisely brain surgery, however it does call for strong plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably tough job. If the old bathtub is easily easily accessible, the job can move rapidly; if you have to open a wall to eliminate the old tub as well as position the new tub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will need an assistant to vacate the old bathtub as well as set in the new one. See to it you have actually qualified on your own for the work as well as are comfortable attempting it. As opposed to working with a specialist to take over a halfway-completed project, it is far better to think about employing one prior to you begin. Chances are you might require a professional plumber to make tube connections.
This write-up will certainly help you mount a brand-new tub in your bathroom if you have actually currently acquired a brand-new tub and also do not need to transform the plan of your previous supply of water pipes.
Your devices as well as product list need to make up the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Planning for the Setup


    To start with, the sustaining frame provided with the bathroom ought to be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to stop pressure on the tub.
    Fit the flexible faucet ports to the bottom of both faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of all of the provided washers.
    Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last position.

    Removing Old Touches


    If you need to change old faucets with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, activate the taps to drain any kind of water remaining in the system. The procedure of removing the existing taps can be rather bothersome as a result of the restricted access that is commonly the instance.
    Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will come from the pipes. When the supply pipelines have actually been gotten rid of, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming during this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
    Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

    Mounting the Bath tub


    Making use of the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are useful in evenly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 small factors.
    The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub till the level checks out level.
    To mount faucets, fit all-time low of the furthest flexible tap adapter to the ideal supply pipeline by making a compression join; then do the same for the various other faucet.
    Turn on the water supply and also examine all joints as well as new pipework for leaks and also tighten them if essential. Fill up the tub and additionally examine the overflow outlet and the typical electrical outlet for leakages.
    Lastly, take care of the bath paneling as described in the manufacturer's instruction manual. Tiling and also securing around the tub ought to wait until the bathtub has actually been utilized at least once as this will certainly resolve it into its final position.

    Suitable New Touches


    If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end gives a link to the existent supply pipelines.
    If you require to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washing machines are in location between the faucet as well as the sink. Secure the faucet in position with the manufacturer given backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal faucet ports. The former kind should be attached to the tap finishes first, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

    Tiling Around the Bath tub


    In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to split a rigid seal, creating the water to penetrate the wall surface between the bathroom and the tiling, causing complications with moisture and also possible leakages to the ceiling below.
    You can select from a selection of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealer can crack relatively very early if you do not take into account this motion prior to sealing.
    Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily offered on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water resistant adhesive as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    As a devoted person who reads about How to Install a Bathtub Yourself, I figured sharing that piece of content was important. I beg you take the opportunity to distribute this content if you appreciated it. Many thanks for taking the time to read it.



    Get An Estimate

    Leave a Reply

    Your email address will not be published. Required fields are marked *